Solution: Disconnect the power, reconnect, replace the fuse, replaced or fixed pulley belt.
解决办法:断开电源,重新连接,更换保险丝,更换皮带或固定皮带轮。
Imagine a belt running over a pulley and catching some loose debris and forcing it around the pulley.
想象一下,一个滑轮皮带运行和捕捉一些松散的碎片,并迫使它周围的滑轮。
Timing Belt: Belt and pulley need replacing between 60-70,000 miles.
同步带:皮带和滑轮之间60 - 70,000需要更换英里。
The chain, pulley, shaft, belt and other running parts should be equipped with protective cover and protective board.
设备上的链条、皮带轮、轴、皮带及其他运转部分都应该设置上防护罩和防护板。
The belt started wrapping up on the tractor pulley.
皮带开始绕在拖拉机的皮带轮上。
Put the V belt on the pulley of the sewing machine.
首先把v 形皮带挂到缝纫机皮带轮上。
Remove front crankshaft belt pulley.
拆卸前曲轴皮带轮。
Minimize belt and pulley wear Reduce noise and vibration Lightweight, only 1-1/4 lbs.
皮带和滑轮磨损最小化降低噪声和振动重量轻,只有1-1/4磅。
Remove water pump belt pulley.
拆下水泵皮带轮。
The greatest stress is produced on all"the static arc"of small belt pulley.
最大应力产生在小带轮的整个“静弧”上。
Tap-Lock Timing BELT pulley with Taper-Lock Bushing is easy on and off, it can be used on variable hubs due to Taper-Lock bushing Bushing bores.
使用锥面紧固衬套安装的锥孔同步带轮,安装、拆卸方便、以配用各种孔径的锥面紧固衬套,就可以适用轴径的安装、使用。
Synchronous belt and cause of damage belt pulley and its c.
同步带及带轮损伤原因及对策。
Place Taper - lock Bushing and Timing Belt Pulley on the transmission shaft.
将锥面紧固套与同步带轮装在传动轮上。
Multi-purpose mini-motorcycle in the belt drive gear for the latter, the main, the size of the driven pulley reduction ratio sub-decision.
在微型摩托车多用皮带传动方式作后传动装置,主、从动皮带轮的大小决定次级减速比。
When the belts have been located in the belt pulley grooves, moves the drive motor away from the driven shaft so that uniform teensioning of the belts is achieved.
在安装新皮带时,要用手动的方式使电机向驱动轴移动而使所有皮带均处于滑轮槽内。
Synchronization is achieved by meshing the belt teeth into a matching similar pitch pulley.
实现同步啮合的带齿成类似的间距滑轮匹配。
Then guide the section of the belt around the air-conditioning compressor belt pulley at the bottom.
然后将皮带从底部绕过空调压缩机皮带轮。
The structure can convert the rotation of a drive belt pulley into the plane curve movement of the pivot bolt, realize motor driving of the stapler and ensure the stapling strength and quality.
采用这样的结构后,可以实现将主动带轮的转动转变为枢轴螺栓的平面曲线运动,实现订扣机的电机驱动,保证订扣力度和订扣质量。
For deficiencies in the design of driving pulley of the belt - convey, carried on analysis and design.
针对带式输送机大型传动滚筒在设计中的不足,对其进行了力学分析和设计。
This paper studies linear actuators based on differential motion of timing belt pulley.
该文研究的是一种新型的基于同步齿型带的差动直线运动机构。
While working , the teeth of belt and the teeth of pulley joggle each other to transmit the motion and the dynamic force.
转动时,通过带齿与带轮的齿槽相吻合来传递动力。
Belt pulley for the output shaft of a gear, gear, electric motor, and output shaft.
用于传动机构输出轴的皮带轮,传动机构,电动机和输出轴。
Its transmission system adopts belt pulley transmission, because leather belt transmission is low in failure transmission, convenient in service and adjustment.
其传动系统采用带轮传动。其传动故障率较低,维修及更换零件方便。
The necessary pulley diameter is defined at a certain radius by the deflection properties of the belt.
这是原文,直译的话,应该是“传动滚筒直径在一定程度上根据皮带跑偏特性来定义。
This thesis studies systematically the mechanics problem of the large-torque pulley of belt conveyor.
本文系统地研究了带式输送机大扭矩传动滚筒的力学问题。
Finally, ensure the belt surround the surface of pulley in loosen condition, then the pulley can be disassembled.
最后,确保皮带松弛地环绕在滚筒表面,这时就可以拆卸掉滚筒了。
Pulley: in mechanics, a wheel that carries a flexible rope, cord, cable, chain, or Belt on its rim.
滑轮:力学上的一种装置,在边缘装有活动绳索、弦、缆、链条或带子的轮。
This paper analyses the structure characteristics of directly turning belt conveyors and gives out the design parameters and layout of the key component-turning pulley.
探讨了直接转弯带式输送机的结构特点,给出了其关键部件转弯滚筒的设计参数和布置方式。
The fan is usually mounted on an extension of the water pump shaft and is driven by V-belt from a pulley mounted on the front end of the cramshaft.
风扇常常装在水泵轴的伸出物上,由安装在曲轴前段的滑轮上的v带驱动。