The influence of the variable ratio on the slip and contact stress is also discovered.

揭示了速比变化比值对齿面滑移及齿面接触应力特性的影响。

But in the textbook about CAM, the contact stress calculating process is seldom discussed.

但在有关凸轮的教科书中，对接触应力的计算过程论述较少。

The plane stress theory is applied to analyze the contact stress between cast track and roll wheel.

采用平面应力理论来分析滚轮与轨道的接触应力问题。

Beased on the theory of Hertz stress, the contact stress of roller bearing is analysed in this paper.

依据赫兹接触强度计算理论，着重研究了圆柱滚子轴承内、外圈及滚动体的接触应力。

Rail-wheel contact stress depends to a large extent on the matching of rail-wheel geometry parameters.

轮轨接触几何参数的匹配优劣直接影响着轮轨接触应力值的大小。

The distribution of the contact stress of FG is obtained in the different meshing locations during the meshing.

获得了在啮合过程中不同的啮合位置面齿轮的接触应力的分布规律。

The influence of pneumatic pressure, sealed pressure and axial diameter on normal contact stress was discussed.

讨论了充气压力、密封压力与充气压力比、轴径对法向接触应力的影响。

In this paper, an electric device is proposed to measure contact stress on the sealing surface of sealing elements.

介绍了西北工业大学研制的密封面接触应力的电测装置。

Sphere contact as object, contact stress and distortion formula of Hertz are deduced theoretically from the modeling.

文中以球体静态接触为对象，建立模型并推导出赫兹接触应力、变形公式。

However the contact stress between slips and casing is very complex, it is extremely difficult to study directly in theory.

然而卡瓦和套管间形成非常复杂的接触压力，从理论上直接研究非常困难。

The definition of rated static torque for linear rolling guide is given according to the criterion for maximum contact stress.

基于最大接触应力的判据，提出滚动直线导轨额定静力矩的基本定义，并计算了几种产品的额定静力矩。

In the mean time, rolling contact stress, braking heat energy, thermal crack and mechanical action are key causes of tread spalling.

其中滚动接触剥离和制动剥离是两种主要剥离类型，滚动接触应力、制动热作用、热裂纹和机械作用是引起剥离的主要原因。

This article presents an analysis of the contact stress of rolls in two-cross-roll straightener and gives a method for the calculation.

在实践的基础上对二辊矫直机辊面接触应力的计算进行了理论分析，给出了辊面接触应力的计算方法。

The contact stress distribution in the rabbet of the aircraft engine blade was determined by combining the experimental and numerical methods.

文中将实验检测技术与数值计算方法相结合，求解飞机发动机叶片榫头上的接触应力分布。

An engineering soft ware adapted to the finite element analysis of three dimensional contact stress in aircraft cylindrical gears is provided.

提供了一个适用于航空圆柱齿轮三维接触应力有限元计算分析的实用工程软件。

Thirdly, the contact stress equations of asymmetric gear with two pressure angles are derived by the Hertz theory of classical contact mechanics.

再次，根据经典接触力学中的赫兹理论推导了双压力角非对称齿轮的齿面接触应力计算公式；

The contact stress is reduced, the life of the wheel, roller and bearings is prolong, it makes autocontrol easy and increases rotate speed of kiln.

降低了接触应力，提高了轮带、托轮和轴承的寿命，便于实现自动控制和提高窑的转速。

In the thesis, the contact stress, bending stress on the root and the contact force on the tooth have been calculated by Finite Element Method (FEM).

文章采用有限元接触计算方法，计算了螺旋锥齿面接触应力和齿根弯曲应力以及齿面接触合力。

The contact fatigue tester has high contact stress, small volume, low noise, low consumption of test sam-pl, stable driving system and reliable results.

认为该装置具有接触应力大，体积小，噪声小，一次试验耗油量小，试验系统传动稳定，试验结果可信等优点。

The curvature radius was derivated and the contact stress of the three-arc-sect isometric type surface was calculated through the elastic dynamics theory.

应用弹性力学理论，推导出接触点的曲率半径，对三弧段等距型面联接进行接触应力计算。

Based on the theory analysis of the equal contact stress inner curve, the experiment research is discussed, and the project of experiment is also designed.

在理论分析等接触应力轨道曲线的基础上，对试验研究进行了探讨，并设计了相应的试验方案。

According to the calculation results, the fatigue life of gears is calculated by limited life design theory and the contact stress and fatigue life are obtained.

根据计算结果，应用齿轮有限寿命设计理论对齿轮疲劳寿命进行计算，得到齿轮的接触应力和疲劳寿命。

On this method, disk roller's contact stress is obtained and the intensity is verficated. It is difficult to calculate accurately the wheel pressure distributing.

常用的链轮闸门轮压计算方法中的平均轮压法的超载系数的确定存在较大的随意性，因此用这种方法计算轮压分布是不合理的。

The elasticity module of ADI is lower than that of steels, so that the surface contact stress borne by ADI gears during working process would be lower than steels.

奥贝球铁材料的弹性模量比钢小，因而奥贝球铁齿轮工作时受到的表面接触应力比钢齿轮小。

In this paper, the calculating method for the contact stress of plate CAM mechanism with translating roller moving follower is presented, and some examples are given.

本文详细分析了对心滚子移动从动件盘形凸轮机构接触应力的计算方法，并给出具体计算例题。

In this thesis the generation of orthogonal - aligned - shaft face gear, finite element analysis (fea) of the bend stress and contact stress of the fg drive are studied.

本文主要研究了正交面齿轮的齿面生成、正交面齿轮传动的弯曲应力和接触应力的有限元分析。

An inverse stochastic boundary element method for prediction of contact stress is presented by combining improved filter algorithm with stochastic boundary element method.

将改进的滤波算法和随机边界元法结合，提出了用于预测接触应力的逆随机边界元法。