The concept of constant shear strain point was proposed.

提出了常剪切应变点的概念。

A stress-strain diagram can be plotted using shear stress and shear strain.

应力-应变图可以用来表现剪切应力与剪切变形。

It is assumed that plastic deformation stems from the localization of shear strain.

岩样的塑性变形假设根源于塑性应变局部化。

Higher DA results in higher values of shear strain and volumetric strain in shear band.

扩容角越大，剪切带最终可以获得越来越高的剪切应变和体积应变。

The constant shear strain point accounting for the degradation of stiffness was discussed.

对考虑刚度劣化时的常剪切应变点进行了讨论。

The strain criterion for ductile shear failure based on the maximum principal shear strain is established.

据此，建立基于最大主剪应变的岩土材料延性剪切破坏应变准则；

The different transformation model can produce different shear strain, so they show different shape memory effect.

采取不同的相变模式产生不同的切变应变，合金获得不同的形状记忆效应。

Elastic shear strain in shear band was dependent on shear elastic modulus, damage variable and residual shear modulus.

考虑刚度劣化后，剪切带的弹性应变由弹性剪切模量、损伤变量及残余剪切模量确定。

The role of shear strain rate of an environmental flow in typhoon propagation is investigated using a shallow water model.

利用浅水波正压模式研究了环境流场切应变率对台风移动的影响。

The shear strain fields are degenerated to be zero under the thin plate situation, so there is no shear locking phenomenon.

由于在薄板情况剪应变退化为零，故不出现剪切闭锁现象。

One dimensional shear strain rate gradient formation of the second order is proposed based on the non-local continuum model.

根据非局部连续介质模型，提出了一维二阶剪切应变率梯度格式。

Moreover, this paper analyses the shear strain and compressive stress and loading frequency dependence of the damping ratio.

另外，对叠层橡胶支座的阻尼比随剪应变、压应力及荷载频率的变化情况进行了分析。

A new concept for large strain-true shear strain-was proposed based on the definition of strain at infinitesimal deformation.

从无穷小变形条件下应变的定义出发，提出了大变形时真实切应变的概念。

At the same time, the effect of stress path circumgyration on shear modulus decreases gradually along with the increase of shear strain.

同时由应力路径旋转对模量的影响也随着剪切应变的增加而逐渐衰减。

Angular stiffness and elastomer shear strain on maximum swinging Angle are important indexes in flexible joint design of solid rocket motor.

角刚度(又称弹性比力矩)及弹性件在最大摆角下的剪切应变是固体发动机柔性接头设计的重要指标。

Results show that the shape of shear stress-shear strain curves is hyperbolic; and no strain-softening phenomenon was observed in the tests.

分析结果表明：黏土—混凝土界面剪应力—剪切位移曲线仍大体呈双曲线形式，并未出现应变软化现象。

Furthermore, a new simplified elastic method called as inherent shear strain method is developed for forecasting fillet weld's angular distortion.

在此基础上，进一步提出了一种用于预测角焊缝角变形的线弹性简化方法，即剪切固有应变法。

This paper discusses also the shear strain modification of rectangular elements as well as a simple analytic method based on data from experiments.

并讨论了矩形单元的剪应变修正问题和基于试验资料而提出的简单分析方法。

Subtracting the elastic strain from the total strain yields the non-local plastic shear strain that depends on the flow stress and the damage variable.

将非局部总应变减去弹性应变，可得剪切带的非局部塑性应变。

The location of shear strain rate localization coincides in position with the location of volumetric strain rate, which is the actual failure zone of rock.

剪切应变率（或应变）局部化区域与体积应变率（或应变）的位置重合，局部化区域就是岩样最终的破坏位置。

The relationship between shear strain and time of Yingkou soft soil is obtained under a series of different cell pressures and different deviator stresses.

利用自行改装后的三轴蠕变仪对海相沉积的营口软土进行蠕变试验，获得了在不同围压、不同偏应力条件下的剪切应变与时间关系数据。

It was found that the amount of the grains broke increased with the shear strain and confining pressure, independent of the initial density of the specimen.

试验表明，颗粒破坏的数量随着剪切变形和侧限压力的增大而增多，与试样的初始密度却无直接关系。

The dynamic properties of the circular tube VE dampers are tested under different environment temperature, excitation frequencies and shear strain amplitudes.

本文对筒式粘弹性阻尼器在不同环境温度、激励频率和应变幅值下的动力性能指标进行了试验研究。

The second shear strain gradient and the function reflecting the effect of strain rate are introduced into the yield function of classical elastoplastic theory.

在经典弹-塑性理论的屈服函数中引入应变梯度及考虑应变率效应的函数。

Higher DA leads to higher value of maximum shear strain increment within the specimen. Therefore, more apparent precursor to failure can be observed at higher DA.

当扩容角较高时，应力峰值时试样内部的最大剪切应变增量较高，因而试样破坏的前兆比较明显。

Compared with the thread obtained by cutting process, the shear strain and hardness of 304 steel pipe thread has been increased significantly after rolling process.

与套丝加工相比，滚压加工后304钢管螺纹的抗剪拉力和硬度均有大幅提高。

The results are shown that the displacement, strain and shear strain of the clay soil foundation under the dynamic loads are larger than those under the static loads.

结果表明，动载比静载作用下的位移、应变、剪应变大得多，特别是对地基的浅表处影响不仅范围大而且深度加大。

The prediction values of shear strain and temperature in shear band based on gradient-dependent plasticity are higher than those by use of classical elastoplastic theory.

由于微结构效应，基于梯度塑性理论的剪切带内部的最大塑性剪切应变及最高温度的预测值高于经典理论的预测值。